欢迎来到日照市岚山区鸿兴木材加工厂的官方网站!

咨询热线:13561989718

建筑方木
方木厂家

栏目导航

新闻动态

联系我们

日照市岚山区鸿兴木材加工厂

联系人:于经理

电话:13561989718

地址:日照市岚山港国际木材加工区

木方生产厂家浅聊建筑木方的规格型号特性

浏览量:   来源:www.hongxingmy.com  作者:鸿兴木材

1、木方生产厂家:建筑木方的规格型号通常分成30*50mm的,这一指的是它的长和宽人们叫35方,这一通常是用于吊棚做木龙骨吊顶用的,或是做某些造型设计的构造用的.60*90的,通常的旧式的家俱的架构就是说用这一做的,但是几乎在家庭装修里很少看见了.120*40的,叫门边方.是用来做门的骨架的,两面在贴上板子喷油漆,一个门就做成了.


1. Wood manufacturer: The specifications and models of building wooden square are usually divided into 30*50mm. This refers to its length and width. People call it 35 sides. This is usually used for hanging shed to make wooden keel suspension roof, or for the construction of some modelling designs. 60*90. Usually the old furniture structure is said to be made of this, but it is seldom seen in family decoration. 120*40 is called door side. Square. It is used as the framework of the door. Paint is sprayed on both sides of the door, and a door is made.




2、一般装修中木方是不用上漆的,在做内部结构的时候有的时候会根据需要刷上防火涂料.


2. In general, wood is not painted in decoration. Sometimes it will be painted with fire retardant paint when it is used for interior structure.




3、基础理论上而言建筑木方能够用在造型设计上,只不过是难题取决于是不是用的美观大方有效,要是美观大方有效没什么原材料和物品是不可以用的,这一关键看室内设计师的功底了.


3. In basic theory, building wooden square can be used in modelling design, but the problem depends on whether it is beautiful and effective. If it is beautiful and effective, there are no raw materials and articles can not be used. This key depends on the foundation of interior designers.




4、上油漆的工艺流程通常是先打腻子粉,把木料的中眼都密死,不然喷出来的漆料非常容易花,随后用打磨砂纸打磨抛光,在喷面漆再打磨抛光,这般不断大概要五次上下,这就叫四遍面漆,随后上边漆,都是相同得用打磨砂纸打磨抛光再喷再打磨,如此反复要三次左右,这就叫三遍面漆.1、木方的规格一般分为30*50毫米的,这个指的是它的长和宽我们叫35方,这个一般是用来吊棚做木龙骨用的,或者做一些造型的内部结构用的.60*90的,一般的老式的家具的框架就是用这个做的,但是几乎在家庭装修里很少看见了.120*40的,叫门边方.是用来做门的骨架的,两面在贴上板子喷油漆,一个门就做成了.


4. The technological process of painting is usually to first polish putty powder, close the middle eyes of wood, otherwise the paint sprayed out will be very easy to flower, then polish with sandpaper, and then polish with spraying paint, which usually takes about five times. This is called four-time finish, and then top paint, which is the same as polishing with sandpaper, then spraying and polishing again, so it needs about three times. It's called three-time topcoat. 1. The specifications of wooden square are generally divided into 30*50 mm. This refers to its length and width. We call it 35 square. This is usually used for hanging shed to make wooden keel, or for making some interior structure of modelling. 60*90. The frame of general old-fashioned furniture is made of this, but it's seldom seen in family decoration. 120*40 is called the side of the door. It's used for doors. Skeleton, two sides on the paste board spray paint, a door made.




2、一般装修中木方是不用上漆的,在做内部结构的时候有的时候会根据需要刷上防火涂料.


2. In general, wood is not painted in decoration. Sometimes it will be painted with fire retardant paint when it is used for interior structure.




3、基础理论上而言建筑木方能够用在造型设计上,只不过是难题取决于是不是用的美观大方有效,要是美观大方有效没什么原材料和物品是不可以用的,这一关键看室内设计师的功底了.


3. In basic theory, building wooden square can be used in modelling design, but the problem depends on whether it is beautiful and effective. If it is beautiful and effective, there are no raw materials and articles can not be used. This key depends on the foundation of interior designers.




4、上油漆的工艺流程通常是先打腻子粉,把木料的中眼都密死,不然喷出来的漆料非常容易花,随后用打磨砂纸打磨抛光,在喷面漆再打磨抛光,这般不断大概要五次上下,这就叫四遍面漆,随后上边漆,都是相同得用打磨砂纸打磨抛光再喷再打磨抛光,这般不断要多次左右,这就叫三遍面漆.


4. The technological process of painting is usually to first polish putty powder, close the middle eyes of wood, otherwise the paint sprayed out will be very easy to flower, then polish with sandpaper, and then polish with spraying paint, which usually takes about five times. This is called four-time finish, and then top paint, which is the same as polishing with sandpaper, then spraying and polishing again. This usually requires many times or so. This is called three-time topcoat.




建筑方木 - 3装修作用 在装修工程中主要是做木龙骨(包括顶棚龙骨和地板龙骨);在土建工程主要是做混凝土模板的楞木;被广泛应用于吊顶、隔墙、实木地板骨架的制作中.


The decoration function of building square wood-3 is mainly to make wooden keel (including roof keel and floor keel); in civil engineering, it is mainly to make concrete formwork of corrugated wood; it is widely used in the manufacture of ceiling, partition wall and solid wood floor skeleton.




建筑木方 - 4选择方式 在家居装修中,建筑木方的制做占一大部分,因此建筑木方的挑选就看起来分外关键.挑选好品质的建筑木方对家居装修的品质有挺大的危害.因而,在选购建筑木方时应当细心选择,主要把好质量管控.


Building Wood Square - 4 Choice in home decoration, building wood square making accounts for a large part, so the selection of building wood square seems particularly critical. Selecting good quality building wood square has great harm to the quality of home decoration. Therefore, when choosing building wood square, careful selection should be made, mainly to control the quality.




木方的含水量在8%~12%为正常,这样在使用的时候才不会出现开裂和起翘的现象.通常木方的含水量与木方的干燥方式有关.蒸汽法的干燥效果最佳,如果有专门的仪器,也可以进行检测.除了这些外,还可以有一些简单易行的方法:


The moisture content of wood square is normal in the range of 8%~12%, so that cracking and warping will not occur when it is used. Usually, the moisture content of wood square is related to the drying method of wood square. Steam drying method has the best drying effect and can be tested if there are special instruments. Besides these, there are some simple and feasible methods:




1.手掂重量法:可以用手掂量掂量木方的重量,含水大的肯定要重一些.


1. Hand weighting method: the weight of wood cube can be weighed by hand, and the water content must be heavier.




2.手摸法:把手放在木方的上面,感受一下它的潮湿程度.


2. Hand touch: Put your hand on the top of the wooden square and feel its humidity.




3.敲钉法:可以用长钉试着钉入木方内,如果很容易钉入的话,说明木方比较干燥,反之,则湿度比较大.


3. Nailing method: long nails can be used to try to nail into the wooden square. If it is easy to nail in, it means that the wooden square is drier. On the contrary, the humidity is higher.




4.抖动法:可以把成品的木方,从一端用力抖动,如果质量不合格的,一般容易从中间一分为二断开.


4. Shaking method: The finished wood can be shaken from one end. If the quality is not up to standard, it is easy to split in two from the middle.




5.眼观法:一根木方,从头到尾总共有多少个节疤,如果节疤显黑色,那就不行,安装的时候易断.


5. Eye view method: how many knots are there in a wooden square from beginning to end? If the knot is black, it will not work. It will break easily when installed.




建筑方木 - 5品质因素 虫害


Construction square wood - 5 quality factors pests




木方在贮存、运送、使用的过程中,会经常受到虫害的影响.木方的天敌是白蚁、天牛、象鼻虫等.如果对木方保护不当,就会受到这些害虫破坏,从而影响了工程木方的质量.


Wood square is often affected by insect pests in the process of storage, transportation and use. Its natural enemies are termites, longicorns, elephants and so on. If it is not properly protected, it will be destroyed by these pests, thus affecting the quality of engineering wood square.




建议,如果是户外用的木方,要用防腐剂浸泡,让防腐剂渗透到木方纤维里面,让木材从里到外变绿,防腐蚀,抵御昆虫攻击.


It is suggested that if it is used outdoors, it should be soaked with preservatives, so that preservatives can penetrate into the wood square fibers, so that the wood can turn green from inside to outside, resist corrosion and resist insect attacks.




裂纹


Crackle




木方的裂纹通常被称作开裂,这是由于木材的纤维之间出现了裂纹,这会使木方的评定等级下降.


Cracks in wooden squares are usually called cracks, which are caused by cracks between the fibers of the wood, which can degrade the grade of the wood squares.




如果木方买回去开裂了,可以用520胶水参合点木屑搅拌,在涂到开裂处,就可以了.


If the wood is cracked, it can be stirred with 520 glue and ginseng joint sawdust and coated on the crack.




腐朽


Decadent




木方在一定条件下会受到木腐菌和细菌的侵害,这些原因会导致木材的颜色和结构发生变化,从而变得松软易碎,呈现出孔状、粉状或者海绵状.这就是木方腐朽的表现.


Wood cube will be damaged by wood rot fungi and bacteria under certain conditions. These reasons will lead to changes in the color and structure of wood, which will become soft and fragile, showing a porous, powdery or spongy shape. This is the manifestation of wood cube decay.




变色


Discoloration




木方发生变色主要是由化学变色和真菌变色两种原因引起.化学变色是因为木方与化学制品相作用,引起的变色现象,真菌变色则是因为真菌生物侵入木方而引起的变色.


The discoloration of wood cube is mainly caused by chemical discoloration and fungal discoloration. Chemical discoloration is caused by the interaction between wood cube and chemical products. Fungal discoloration is caused by fungal organisms invading wood cube.




变形


deformation




木方变形主要是由于在加工、干燥、贮存的过程引起的翘曲变形和扭曲变形,


Wood square deformation is mainly caused by warpage and distortion during processing, drying and storage.